Forum für Wissenschaft, Industrie und Wirtschaft

Home Fachgebiete Physik Astronomie Nachricht

Scientists looking to burst the superconductivity bubble

nächste Meldung

In a study published today, Monday, 16 may, in IOP Publishing's journal Superconductor Science and Technology, researchers have examined bismuth strontium calcium copper oxide (Bi2Sr2CaCu2Ox, Bi2212) – one of the most promising superconducting materials capable of creating large magnetic fields way beyond the limit of existing magnets – and found that its capabilities are limited by the formation of bubbles during its fabrication process.

Bi2212 is the only high temperature superconductor capable of being made into round wire, providing the preferred flexibility in magnet construction, and giving it potential uses in medical imaging and particle accelerators, such as the Large Hadron Collider in Switzerland.

For magnet applications, these wires must exhibit a high critical current density - the current density at which electrical resistance develops - and sustain it under large magnetic fields. This remains a stumbling block for utilising the huge potential of Bi2212 in the magnet technology as compellingly high critical current densities have not yet been achieved.

Previous studies have shown that a critical current varies widely between Bi2212 wire lengths – the critical current in wires that were 50 to 200m long was 20 to 50% lower than in 5 to 10cm long samples. This led the researchers, from the Applied Superconductivity Centre and the National High Magnetic Field Laboratory, Florida State University, to conclude that this variability must be caused by the connectivity of Bi2212 grains within the wires.

Bi2212 wires, made up of multiple filaments, are fabricated using the powder-in-tube (PIT) method in which Bi2212 powder is packed inside silver tubes and drawn to the desired size. The filaments of Bi2212 powder must firstly be melted inside their silver sheath and then slowly cooled to allow the Bi2212 to reform, greatly enhancing the critical current density.

As the processes between the critical melt and re-growth step is still largely unknown, the researchers decided to rapidly cool samples at different times in the melting process in order to get a snapshot of what occurs inside Bi2212 wires.

Using a scanning electron microscope and synchrotron X-ray microtomography, the researchers observed that the small powder pores, inherent to the PIT process, agglomerate into large bubbles on entering the melting stage.

The consequences of this are major as the Bi2212 filaments become divided into discrete segments of excellent connectivity which are then blocked by the residual bubbles, greatly reducing the long-range filament connectivity, and strongly suppressing the flow of current.

The new findings suggest that a key approach to improve the critical current density of the material would be to make it denser before melting.

Lead author Dr Fumitake Kametani, of The Applied Superconductivity Centre, Florida State University, said, "Our study suggested that a large portion of bubbles originates from the 30-40% of empty space, inevitable in any powder-in-tube process, which requires particle rolling to allow deformation of the metal-powder composite wire. "

"Densification of the filaments at final size - increasing the powder-packing density from 60-70% to greater than 90% - is an excellent way to reduce or eliminate the bubble formation. Various densification processes are now being tested."

From Monday, 16 May, the journal paper can be found at http://iopscience.iop.org/0953-2048/24/7/075009)

Notes to EditorsContact

1. For further information, a full draft of the journal paper or contact with one of the researchers, contact IOP Publishing Press Assistant, Michael Bishop:
Tel: 0117 930 1032
Email: Michael.bishop@iop.org

Bubble formation with filaments of melt processed Bi2212 wires and its strongly negative effect on the critical current density

2. The published version of the paper "Bubble formation with filaments of melt processed Bi2212 wires and its strongly negative effect on the critical current density" (Superconductor Science & Technology 24 075009) will be freely available online from Monday, 16 May. It will be available at http://iopscience.iop.org/0953-2048/24/7/075009)

Superconductor Science and Technology

3. Superconductor Science and Technology, founded in 1988, is the leading journal for all aspects of superconductivity with the highest impact factor of all journals specialising in this field.

IOP Publishing

4. IOP Publishing provides publications through which leading-edge scientific research is distributed worldwide. IOP Publishing is central to the Institute of Physics (IOP), a not-for-profit society. Any financial surplus earned by IOP Publishing goes to support science through the activities of IOP.Beyond our traditional journals programme, we make high-value scientific information easily accessible through an ever-evolving portfolio of community websites, magazines, conference proceedings and a multitude of electronic services. Focused on making the most of new technologies, we're continually improving our electronic interfaces to make it easier for researchers to find exactly what they need, when they need it, in the format that suits them best. Go to http://publishing.iop.org/.

The Institute of Physics

5. The Institute of Physics is a scientific charity devoted to increasing the practice, understanding and application of physics.

It has a worldwide membership of around 40 000 and is a leading communicator of physics-related science to all audiences, from specialists through to government and the general public. Its publishing company, IOP Publishing, is a world leader in scientific publishing and the electronic dissemination of physics. Go to www.iop.org

Michael Bishop | Quelle: EurekAlert!
Weitere Informationen: www.iop.org

nächste Meldung