Forum für Wissenschaft, Industrie und Wirtschaft

Hauptsponsoren:     3M 


A new look at wetting models: Continuum analysis

The wetting model is a classical problem in surface science and biomimetic science. Professor LIU Jianlin and his collaborators from China University of Petroleum, Wuhan University and Fourth Military Medical University approached this old and classical problem from a new direction.

They stressed that it is the triple contact line and not the contact area of the droplet/solid interface that determines the macroscopic contact angle. The proposed continuum model, termed the mechanism-based model, can illustrate the contact line pinning effect at some wedges or phase interfaces between different materials. Their work, entitled "A new look on wetting models: continuum analysis", was published in SCIENCE CHINA Physics, Mech & Astro, 2012, Issue 11.

The concept of the contact angle dates back to the pioneering contribution of Young, which was a milestone in the characterization of the wetting property of a perfectly smooth and homogeneous solid surface. However, many experiments have shown that most wetting and dewetting behaviors of solid are not only related to the chemical components but also closely related the micro- and/or nano-structures of their surfaces. The combination of wetting properties and geometric topographies of the surface often renders a wealth of attractive phenomena in nature and daily life. For example, the "lotus effect", that is, the self-cleaning capability of lotus leaves, is due to the intrinsic hydrophobicity and micro/nanomorphologies of surfaces. Some aquatic creatures, such as the water strider, water spider and mosquito, resort to their superhydrophobic capacities to stand, walk and jump on still or even flowing water.

This skill originates from the special micro/nano setae and nanoridge structures on their legs, which can produce extremely large driving forces to support their body weight. The Stenocara beetle of the Namib Desert is a dew-collector, possessing special surface microstructures with variable hydrophilic and hydrophobic domains on its carapace. A new approach for achieving special wetting surfaces has been proposed and advanced by varying the chemical compositions and geometrical topographies.

A plethora of superhydrophobic surfaces with static contact angles larger than 150° were prepared to produce ultra-hydrophobicity with fractal or hierarchical surface structures, to mimic the biological materials. These designed rough and heterogeneous surfaces have already been put into use in various areas of industry, spanning from porous media, microfluidic devices, and self-cleaning paints to glass windows.

For these natural phenomena and superhydrophobic (or superhydrophilic) materials, a critical issue is how to predict the wetting behaviors properly, which is of great value to both fundamental science and engineering applications. As is well known, there are two classical models with which to examine the macroscopic contact angle on a rough or heterogeneous substrate; i.e., the Wenzel model and the Cassie–Baxter model. The Wenzel model indicates that part of the liquid completely pierces into the microstructures on the rough solid substrate and the geometric topographies amplify the hydrophobicity of hydrophobic surfaces and enhance the hydrophilicity of hydrophilic surfaces. The Cassie model deals with a substrate with several phases of different wetting properties, implying that the macroscopic contact angle is actually the weighted average function of different hydrophilicities of the materials.

Although Wenzel and Cassie models can successfully elucidate the superhydrophobic phenomenon of inhomogeneous substrates, some scientists doubted the accuracy of these results. They designed experiments to demonstrate that the contact line and not the contact area beneath the droplet is responsible for the macroscopic contact angle. These disputes suggest that the Wenzel and Cassie models are only valid in a certain range, but to what extent the two models apply is a key subject of investigation. Therefore, the present work is not to invalidate the Wenzel and Cassie models, but is directed toward a further understanding of the wetting mechanism based upon the triple contact line, from a new viewpoint of continuum mechanics. This theory of wetting is constructed on a strong theoretical basis, including consideration of the force equilibrium and energy, which deals with a more general substrate, say, a rough and chemically heterogeneous solid surface.

Using the energy formulation and considering the movable boundary condition, the authors derived the macroscopic contact angle on a rough and heterogeneous substrate, under the assumption that the Young's contact angle and interfacial energies are all field functions of the position of the contact line. The equation of the relationship shows that the macroscopic contact angle has no direct connection with the gravity of the droplet. Besides, the macroscopic contact angle strongly depends on the geometrical and chemical properties of the substrate, as it is a continuum field variable at any point. This means that different positions will have different contact angles. Finally, the result again emphasizes that the macroscopic contact angle is dependent only on the properties of the triple contact line and is independent of those of the area underneath the droplet. However, the classical Wenzel and Cassie models are both concerned with the geometrical and chemical properties of the contact zone, and not the contact point. In the following, the authors designed several substrates with special roughnesses and hydrophilicities, and compared the results predicted by the Wenzel model, Cassie model and the mechanism-based model. The results show that the mechanism-based model deviates from the classical models greatly for these types of substrates, and this conclusion suggests that the Wenzel and Cassie models only hold in a certain range.

The mechanism-based model can also be adopted to explore the pinning effect due to a wedge or different hydrophilicity phases. At a sharp wedge, the derivative of the substrate curve is discontinuous, and the macroscopic contact angle does not have a determinate value. In reality, there are no pure "sharp" or "jump" points, and these sharp tips have small curvature radii. In particular, a fine AFM tip may take a radius of several tens of nanometers. The curvature at the singular point can be enlarged, and in this narrow domain, the derivative of the substrate can change from zero to the value when the triple contact line is located on the inclined side of the wedge. In the real world, this transition zone near the sharp tip is too minute to be observed. Therefore, the triple contact line is often regarded as being "pinned" at this position, and only variation in the contact angle is macroscopically seen. Similarly, we can consider a substrate only including two phases with different contact angles. This pinning phenomenon is really a "black box" used to find of a solution employing the developed classical model. Mathematically, there is no wetting property jump at the interface of two different materials binding together. Indeed, there is also a transition zone owing to the atom diffusion, where the width is reported as several tens of micrometers. In this area, the gradient of the wetting property is very abrupt, spanning from a smaller value to a larger value, and the motion of the triple contact line cannot be observed by the naked eye. The only phenomenon is that the contact angle at this point (in fact in this area) continuously increases with an increasing droplet volume.

This study investigated the wetting model for a general substrate from a new viewpoint of continuum mechanics, and the analyses first showed how the Wenzel and Cassie models deviate from the experimental results, and then elucidated the motion of the triple contact line. The result shows that the contact angle is independent of the gravity of the droplet and the contact area underneath the droplet, and is only dependent on the property of the triple contact line . Several substrates with typical geometric topographies and chemical components were provided as examples to demonstrate the difference between the classical models and mechanism-based models. The derived model can also illustrate the pinning effects on a sharp wedge or at the interface between two different phases by employing continuum field theory. This continuum model also casts light on the pinning effect on a sharp wedge or at the interface between two different phases. The investigation revisits the fundamentals of wetting on rough and heterogeneous substrates, which will help in the design of super-hydrophobic materials and provide the predictions required to engineer novel microfluidic devices.

See the article: Liu J L, Xua R, Zhou X H. A new look on wetting models: continuum analysis. SCI CHINA Phys, Mech & Astro, 2012(11):2158-2166

LIU Jianlin | EurekAlert!
Further information:

More articles from Physics and Astronomy:

nachricht Spiral arms: not just in galaxies
30.09.2016 | Max-Planck-Institut für Radioastronomie

nachricht Discovery of an Extragalactic Hot Molecular Core
29.09.2016 | National Astronomical Observatory of Japan

All articles from Physics and Astronomy >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: First-Ever 3D Printed Excavator Project Advances Large-Scale Additive Manufacturing R&D

Heavy construction machinery is the focus of Oak Ridge National Laboratory’s latest advance in additive manufacturing research. With industry partners and university students, ORNL researchers are designing and producing the world’s first 3D printed excavator, a prototype that will leverage large-scale AM technologies and explore the feasibility of printing with metal alloys.

Increasing the size and speed of metal-based 3D printing techniques, using low-cost alloys like steel and aluminum, could create new industrial applications...

Im Focus: Zielsichere Roboter im Mikromaßstab

Dank einer halbseitigen Beschichtung mit Kohlenstoff lassen sich Mikroschwimmer durch Licht antreiben und steuern

Manche Bakterien zieht es zum Licht, andere in die Dunkelheit. Den einen ermöglicht dieses phototaktische Verhalten, die Sonnenenergie möglichst effizient für...

Im Focus: Experimentalphysik - Protonenstrahlung nach explosiver Vorarbeit

LMU-Physiker haben mit Nanopartikeln und Laserlicht Protonenstrahlung produziert. Sie könnte künftig neue Wege in der Strahlungsmedizin eröffnen und bei der Tumorbekämpfung helfen.

Stark gebündeltes Licht entwickelt eine enorme Kraft. Ein Team um Professor Jörg Schreiber vom Lehrstuhl für Experimentalphysik - Medizinische Physik der LMU...

Im Focus: Der perfekte Sonnensturm

Ein geomagnetischer Sturm hat sich als Glücksfall für die Wissenschaft erwiesen. Jahrzehnte rätselte die Forschung, wie hoch energetische Partikel, die auf die Magnetosphäre der Erde treffen, wieder verschwinden. Jetzt hat Yuri Shprits vom Deutschen GeoForschungsZentrum GFZ und der Universität Potsdam mit einem internationalen Team eine Erklärung gefunden: Entscheidend für den Verlust an Teilchen ist, wie schnell die Partikel sind. Shprits: „Das hilft uns auch, Prozesse auf der Sonne, auf anderen Planeten und sogar in fernen Galaxien zu verstehen.“ Er fügt hinzu: „Die Studie wird uns überdies helfen, das ‚Weltraumwetter‘ besser vorherzusagen und damit wertvolle Satelliten zu schützen.“

Ein geomagnetischer Sturm am 17. Januar 2013 hat sich als Glücksfall für die Wissenschaft erwiesen. Der Sonnensturm ermöglichte einzigartige Beobachtungen, die...

Im Focus: New welding process joins dissimilar sheets better

Friction stir welding is a still-young and thus often unfamiliar pressure welding process for joining flat components and semi-finished components made of light metals.
Scientists at the University of Stuttgart have now developed two new process variants that will considerably expand the areas of application for friction stir welding.
Technologie-Lizenz-Büro (TLB) GmbH supports the University of Stuttgart in patenting and marketing its innovations.

Friction stir welding is a still-young and thus often unfamiliar pressure welding process for joining flat components and semi-finished components made of...

Alle Focus-News des Innovations-reports >>>



im innovations-report
in Kooperation mit academics

Smart Glasses Experience Day

30.09.2016 | Veranstaltungen

Einzug von Industrie 4.0 und Digitalisierung im Südwesten - Innovationstag der SmartFactoryKL

30.09.2016 | Veranstaltungen

"Physics of Cancer" - Forscher diskutieren über biomechanische Eigenschaften von Krebszellen

30.09.2016 | Veranstaltungen

Weitere VideoLinks >>>
Aktuelle Beiträge

Smart Glasses Experience Day

30.09.2016 | Veranstaltungsnachrichten

Materialkompetenz für den Leichtbau: Fraunhofer IMWS präsentiert neue Lösungen auf der K-Messe

30.09.2016 | Messenachrichten

Vom Rollstuhl auf das Liegerad – Mit Funktioneller Elektrostimulation zum Cybathlon

30.09.2016 | Energie und Elektrotechnik